Honeywell RTH230B juhend

Honeywell RTH230B
9.2 · 2
PDF juhend
 · 4 lehekülge
Inglise
juhendHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Vaadake Honeywell RTH230B juhendit tasuta siin. See juhend kuulub kategooriasse termostaat ja seda on hinnanud 2 inimest, kelle keskmine hinnang on 9.2. See juhend on saadaval järgmistes keeltes: Inglise. Kas teil on küsimus toote Honeywell RTH230B kohta või vajate abi? Esitage oma küsimus siin

Vajate abi?

Kas teil on küsimus kaubamärgi Honeywell mudeli kohta ja vastust pole juhendis?

  • Saage lahenduste kohta värskendusi
  • Saage oma küsimusele vastuseid

Küsimus ja vastus

Küsimuste arv: 0

Honeywell RTH230B on programmeeritav termostaat, mis sobib paljudele kodudele ja kontoriruumidele. See võimaldab teil programmeerida oma kütteseadmeid erinevatel kellaegadel, et saavutada soovitud keskkonnatingimusi. Termostaatil on digitaalne ekraan, mis kuvab selgelt kitsendatud andmeid, näiteks temperatuuri ja programmeeritud seadeid. Nutikas disain võimaldab teil programmeerida kütteseadmeid nädala järgi, et tagada soovitud temperatuur kogu päeva vältel. Lisaks sellele on Honeywell RTH230B-l mitu energiatarbimise programmeeringut, mis aitavad vähendada energiakulusid ja aidata energiat säästa. Termostaadil on ka tagasilöögikaitse, mis kaitseb seadet pinge languse ja katkestuste eest. Käepärane taimer võimaldab teil seadistada teavituse soovitud ajaks, et võite tuleviku temperatuure lihtsalt kohandada. Kõik need funktsioonid muudavad Honeywell RTH230B-d optimaalseks lahenduseks neile, kes soovivad kodus mugavat temperatuuri kontrollida ja samal ajal oma energiakulusid hoida.

Üldine
KaubamärkHoneywell
MudelRTH230B
Toodetermostaadid
KeelInglise
FailitüüpKasutusjuhend (PDF)

Te ei leia juhendist oma küsimusele vastust? Te võite leida vastuse oma küsimusele kaubamärgi Honeywell mudeli RTH230B kohta allpool.

Kus on parim koht termostaadi jaoks?

Parim koht termostaadi jaoks on ruum, kus veedate kõige rohkem aega, paljudel juhtudel elutuba või köök. Asetage termostaat umbes poolteist meetrit põrandast kõrgemale, mitte päikese kätte ega mitte välisseinale.

Mis on termostaadi surnud tsoon?

Kui teie termostaadil on surnud tsoon, on teie seade justkui puhkeolekus. Termostaat lülitub sisse ainult siis, kui erinevus erineb seatud toatemperatuurist rohkem kui 2 ˚C.

Milline on ideaalne toatemperatuur?

Enamik inimesi leiab, et ideaalne toatemperatuur on vahemikus 19 kuni 22 kraadi Celsiuse järgi.

Kas toote Honeywell RTH230B juhend on Eesti Keel keeles saadaval?

Kahjuks ei ole meil toote Honeywell RTH230B juhend Eesti Keel keeles saadaval. See juhend on saadaval Inglise keeles.

Kas teie küsimust ei ole loendis? Esitage oma küsimus siin

Tulemused puuduvad